Request a Consultation

Installation that starts below the floor.

Solid wood, engineered and prefinished hardwood installed across San Diego County. Subfloor leveling and moisture testing included. Wide plank and herringbone.

Materials

Solid, engineered, prefinished, laminate

Subfloor

Measured, leveled and moisture-tested first

On site

Four to six days for 1,000 sq ft

Quote

Written, within 24 hours of the visit

Most flooring failures are subfloor failures.

Cupping. Gaps that open along a whole run. Boards that click or give underfoot. A finish that wears through in one corner years before the rest. Almost none of these are problems with the wood. They are problems with what the wood was laid on, and with the moisture conditions on the day it was laid.

So every installation we quote begins below the finished floor. Where the existing floor can be lifted or the substrate reached, we measure flatness rather than assuming it, test the moisture content of both the subfloor and the material, and identify what correction is required before anything is fastened down. Leveling enters the conversation before price does, because a quote that leaves it out is not cheaper. It is just incomplete.

A laser level and a marked board before the first row goes down
Flatness checked before a board goes down
A wide plank face up, the knot and grain visible
Wide plank, face up

Materials

Solid wood

One piece of timber through its full thickness, which is why it can be sanded and refinished several times across its life and realistically outlast you in the house. Best over a wood subfloor, at or above grade. It moves with humidity, so it needs room to move.

Engineered wood

A real hardwood wear layer over a cross-laminated core that resists the seasonal movement solid wood cannot. The right answer over a concrete slab, in coastal homes, and anywhere with radiant heat. Ask about the wear layer: a thick one refinishes, a thin one never will.

Prefinished

Boards finished under factory conditions, with a cure and a warranty no job site can match. Installed and walked on the same day, with no sanding, no coats and no cure time in your house. We also refinish these floors later, which most contractors will not do.

Bundles of unfinished hardwood strips stacked in the room, acclimating before installation
Material delivered ahead of time, acclimating in the room where it will live.
Moisture and acclimation

Wood keeps moving after it is delivered. Coastal San Diego makes that a real variable.

Hardwood takes on and gives off moisture with the air around it, expanding and contracting as it does. A floor installed while the boards are still adjusting to the house will move afterwards, and that movement is what becomes cupping in one home and open seams in another.

More on moisture and acclimation

So the material is delivered ahead of installation and left to acclimate in the actual rooms, not in a garage or a hallway. We meter the wood and the subfloor and start when the two are in range, not on the day the calendar says. In homes near the water, and over any concrete slab, that gap is wider and engineered construction is frequently the answer rather than solid. Not as a downgrade, but because it is the product built for that condition.

Expansion space at the walls, correct fastening for the substrate, and the right underlayment or adhesive are the rest of it. None of this is visible in a finished room. All of it decides what the room looks like in five years.

Nobody ever sees the subfloor. It decides how the room looks in five years.

Flatness, moisture readings and acclimation, before a single board goes down.
Species, widths and patterns

Width and pattern change the room, not just the floor.

White oak is what most of this market is specifying, and for good reason: a neutral, slightly cool base that takes stain predictably and sits under almost any palette without fighting it. Red oak is harder-wearing than its reputation and costs less, but carries a warm pink undertone that will read through a light or gray stain, which is worth knowing before you choose the color rather than after. Walnut is darker, softer underfoot and quietly expensive, and it shows wear sooner in a busy household. Maple is very hard and very tight-grained, which means it resists dents and resists stain in equal measure, and is best left close to natural.

More on species, widths and patterns

Wide plank reads calmer and more contemporary, with fewer seams across the field of view and more of each board's figure visible. It also demands a flatter subfloor than narrow material, because a wide board bridges a dip instead of following it, which is why leveling comes up early in any wide plank quote.

Herringbone and chevron add structure and formality, and they change the geometry of a room rather than just its surface. Both cost more in material and considerably more in labor, and both reward a room with the proportions and the sightlines to carry them. In a narrow space they fight the architecture instead of serving it.

Narrow strip reads traditional and is often simply the correct answer when matching an existing floor elsewhere in the house, where a change in width at a doorway would be more conspicuous than a change in color.

There is one decision underneath all of these: which direction the boards run. Along the longest dimension of the space makes a room read longer. Perpendicular to the main window makes incoming light travel across the grain rather than down it, which flattens the floor visually. We walk the room and look at where the light actually comes from before deciding, rather than defaulting to the direction that is fastest to install.

Every stain color is available, including custom mixes. One piece of advice worth more than any sample: look at the color on your own floor, under your own light, at the hour you use the room most. Showroom lighting has sold a lot of floors that people later regret.

Bring the plans, or bring the room. We quote from what is actually there.

Request a Consultation

How it runs.

01

Consultation and measurement

Species, width, pattern and direction decided against the light in your room.

02

Assessment

Flatness and moisture measured, in the substrate and in the material, before a price is written.

03

Preparation and acclimation

Subfloor corrected; material left in the rooms where it will live until it is in range.

04

Installation

Boards laid with attention to grain, light and where the seams land.

05

Finishing and final inspection

Dustless sanding and Rubio Monocoat or Bona where the material is unfinished, then a walk at a raking angle.

4–6days for 1,000 sq ft
24hbefore socks on the floor
3days before furniture returns
24hfor the written quote

Add time for subfloor leveling, for herringbone and chevron, for stairs, and for unfinished material that is sanded in place after it is laid.

New construction

Builders and general contractors.

We work new construction and full remodels alongside other trades, and we schedule around the sequence rather than against it. Flooring goes in late enough that the wet trades are finished and the building has dried, and early enough not to become the item holding up a closing.

On occupied or phased projects we can split the work by floor, by wing or by unit, and hold the finishing until the rest of the site stops generating dust. We carry our own insurance, we provide certificates on request, and we are used to HOA requirements, building access windows and elevator reservations in the condo and coastal properties around San Diego.

If a project calls for luxury vinyl plank or laminate instead of wood, we install those to the same standard. See Vinyl & Laminate

Planning an installation?

Free on-site consultation, written quote within 24 hours.